ANET AM8 Notes

Assembly notes (both A8 & AM8)

  • Reverse cross brace on heat bed H frame as this flatterns the belt path
  • The extruder fan can is only fixed by the 2 M3x45 Cap Head Socket screws, so add 2 M3 screws through the fan guard and fan into the heatsink fins
  • The heat break needs to be firmly abutting the nozzle, so loosen the nozzle, and get the heat break in just far enough that the nozzle butts up against it and the block, takes a few goes to get it right

RRIG

2 x V-SLOT 2040 Aluminium Extrusion – Natural Anodized 340mm
3 x V-SLOT 2040 Aluminium Extrusion – Natural Anodized 313mm
2 x V-SLOT 2040 Aluminium Extrusion – Natural Anodized 440mm (PRE-TAPPED)

120 x Tee Nut

6 x Natural Anodized Double Corner brackets
4 x Natural Anodized Single Corner brackets
32 x Button Head Screws M5 (Single) (Length: 8mm)

80 x Button Head Screws M5 (Single) (Length: 10mm)
8 x M3 Washer
8 x M5x10mm Socket Head Cap Screw

6 x Rubber Bumper Foot (bumper only)
6 x Button Head Screws M5 (Single) (Length: 14mm)


MFM Frame

Bottom frame sides: 2 x 340mm 2040 / 364mm 2040)

  • Tapped M6 all holes
  • 340mm Hex key access holes 127mm – 20mm + 10mm = 117mm from end
  • 364mm Hex key access holes 139mm – 20mm + 10mm = 129mm from end

Vertical Sides: 2 x 440mm 2040

  • These are tapped on other kits, why= bottom plastic bracket?
  • Bottoms tapped both holes
  • Top milled sideways for M6 Cap Screw

Bottom Horizontals: 2 x 313mm 2040

  • Mill for M6 Screws x 2 each end

Top Horizontal: 1 x 313mm 2040

  • Threaded all holes M6 Screws

NO CORNER BRACKETS NEEDED RRIG = 6 Double, 4 single + nuts/screws not required


Milling for M6 end on joints:

  • Bolt Head is 10mm, Mill @ 10.5mm for bolt head, possibly 11 if tolerances shift too much
  • 6.35 (1/4″) mm through, with drill as short as possible, center punching manually for now to prevent walking annoying as it is

Milling for M5 joints

  • Bolt Head is 8.4mm, Mill @ 10mm
  • 5.5mm, no center punching but keeping drill bit as short as possible in collet

20180302 2nd build parts list:

  • 8 x M6x30mm Hex Cap Head screws
  • 4 x M6x20 Hex Button Head screws
  • 4 x M5x20 Hex Button Head screws + 4 x M5 T-Slot Block nuts
  • 4 x Rubber feet + 4 x M4x8 Hex Button Head screws + 4 x M4 T-Slot Block nuts

20180302 Revised with Flat plates for vertical bracing

  • 1 x 313 top cross member
    • threaded 4 x end bores M6 to 20mm
  • 2 x 305mm base top/bottom members
    • each milled x 4 to accept recessed M6 Cap head bolt for fixing to base side mebers
  • 2 x 364mm base side members
    • each with threaded 4 x end bores M6 to 20mm
    • each milled x 2 to accept recessed M5 Cap head bolt for fixing to verticals
  • 2 x 440mm verticals
    • each with 2 x hex key access holes at top
    • Vertical plates:
    • 2 x Flat brackets
    • 5 x M5 x Cap head Screws

Misc Hardware

  • Joint Cross Member to Verticals
    • 4 x M6x20mm Button Head
  • Base corners
    • 8 x M6x30mm Cap Head
  • Base side to Verticals
    • 2 x Flat Corner Alum Brackets
    • 4 x M5x25 Hex Cap Screw + 4 x (2 per bolt to get distance right) x  M5 DIN125 Washers + 4 x M5 2020 Block Nuts
    • 6 x M5x12 Hex Cap Screws + 6 x M5 DIN125 Washers + 6 x M5 2020 Block Nuts
  • Joint Cross Member to Verticals optional Alum brackets:
    • 2 x Flat Corner Alum Brackets
    • 10 x M5x12 Hex Cap Screws +10 x M5 DIN125 Washers + 10 x M5 2020 Block Nut
  • 4 x Feet + 4 x M4 x 10mm Button Head + 4 x M4 Hammer nuts

Frame assembly inserting captive T-Block nuts:

  • Base rear member:
    • Y Motor bracket: Insert T-Block nuts: 1 on top slot

Assembly (assumes frame is assembled first)

  • Y Rod Holders (x3), Y Rod Holder for Y Microswitch (x1) (Printed)
    • Tensioning screws
      • 4 x M3 Nuts
      • 4 x M3 x 10mm screws
    • Rod Holders to frame
      • 8 x M5 x 12mm Button Head Hex Screws + Washers (Button needed as Cap Head are too high and interfere with leveling screws
      • 8 x M5 Hammer Nuts
      • Note right rear is the Y Rod Holder for Microswitch
      • Leave loose for alignment later
    • Y End Stop Microswitch
      • 2 x small self tapping screws
  • Y Motor Bracket (Printed)
    • Bracket to frame
      • 1 x M5 T-Block Nut +
      • 2 x M5 Hammer nuts +
      • 3 x M5 x 12mm Cap Head Hex Screws +
      • 3 x M5 Washers +
      • Leave loose for alignment later
  • Y Motor to Bracket:
    • 4 x ANet M3x10mm screws
    • 4 x DIN9021 M3 Washers +
  • Belt Tensioner Block & Tensioner (Printed)
    • Block to frame (leave loose for alignment later)
      • 2 x M5 T-Block Nuts +
      • 2 x M5 x 12mm Cap Screws + Washers
      • Leave loose for alignment later
    • Tensioner into Block
      • 1 x M3 Nut
      • 1 x M3 x10mm screw
      • Insert M3 captive nut into Tensioner
      • Thread M3 x 10mm screw through into captive nut just enough to hold nut in place for now
      • Slide Tensioner into Block
    • Belt idler bearings into Tensioner
      • 1 x M3 x 30mm Screw + M3 Lock Nut
      • 2 x Flanged bearings
  • Z End Stop Bracket (Printed)
    • 2 x M5 x 10mm Button head Screws
    • 2 x M5 T-Block nuts
    • Fix microswitch using original self tapping screws
  • Z Motor Bracket (x2 Left, Right) (Printed)
    • Bracket to frame
      • 8 x M5 T-Block Nuts +
      • 8 x M5 x 10mm Cap Head Socket screws + Washers (Must be cap head for recessed screws
      • Position bracket so top of bracket is 25mm above top of the frame
  • Z Motors to Brackets (x2)
    • 4 x M3x10mm screws
    • 4 x DIN9021 M3 Washers +
  • Z Axis Top Brackets (x2, Left, Right) (Printed)
    • 2 x M5 x 10mm Cap Head Socket Screws (For recessed holes)
    • 6 x M5 x 12mm Cap Head Socket Screws
    • 8 x M5 T-Block Nuts
  • LCD Panel Case (Printed) to Brackets (2x, Left, Right) (Printed)
    • Assemble the LCD / Case / BracketsInsert 4 x captive M3 nuts into the 2 brackets
      • Sit the panel into the case
      • Attach the 2 x brackets to the case using M3 screws
    • Bolt the completed LCD Panel to the frame
      • 4 x M5 x 10 Button Head screws
      • 4 x M5 Swivel in nut
  • Control Board / Bracket
    • Control board bracket
      • 4 x M3 screws
      • 4 x M3 Spacers
      • 4 x M3 Nuts
    • Bracket to frame
      • 2 x M5 x 10mm Button head screws
      • 2 x M5 hammer nuts

Y Carriage

  • Carefully insert rods into rod holders
  • Word down 1 side, positioning the outside edge of the 8mm shaft 67.5mm in from the outside edge of the frame base

71+ 65 = 135 -> 135/2 = 67.5mm outside of 8mm shaft to outside edge of frame (for 313mm wide version


Other optional upgrades:

  • Replaced 4 x LM8UU on Y Axis (on heat bed) with Plastic bearings
  • Replaced 2 x LM8LUU on Z Axis with 4 x Plastic bearings
  • Turned Heatbed H-Plate upside down to get Y belt path flat
  • Heat bed to H-Plate mounts:
    • Drilled out M3 threads on H Plate
    • Added extra washers:
      • M3 Countersunk screw as provided through (in order):
        • Heat bed
        • M3 Nylon washer
        • M3 Washer
        • M4 9021 washer
        • M3 Washer
        • Spring
        • M4 9021 washer
        • H Plate
        • M3 DIN9021 Washer
        • M3 DX Beveled adjustment nut (Because I can’t remember if A8 kit came with Wing nuts or not)